DRAG DROP
Refer to the exhibit. Drag and drop the EVC configuration items from the left onto the correct descriptions on the right.
Select and Place:
Refer to the exhibit. A network engineer has been called to configure the four PE devices in order to enable full communication among the four CE devices connected to them. While starting to configure, he experienced a connectivity issue. Which two tasks should the engineer perform in order to begin the process correctly? (Choose two.)
A. Configure PE3 to export route-targets 100:1 and 200:2.
B. Configure PE3 to import route-targets 100:1 and 200:2.
C. Configure PE4 to import route-targets 101:1 and 202:2.
D. Configure PE2 to export route-targets 300:3 and 400:4.
E. Configure PE1 to import route-targets 300:3 and 400:4.
Refer to the exhibit. If the two devices are operating normally, which two conclusions can you draw from this configuration? (Choose two.)
A. CE1 must use OSPF to establish a neighbor relationship with PE1.
B. PE1 labels the routes it learns from CE1 with the route-target 222:2 and shares them with its VPNv4 peers.
C. PE1 labels the routes it learns from CE1 with the route-target 111:1 and shares them with its VPNv4 peers.
D. The PE-CE routes between the devices are being exchanged by OSPF
E. CE1 is supporting CSC.
Which two are characteristics of using a non-MPLS peer-to-peer model over a traditional overlay model? (Choose two.)
A. The model is suited for nonredundant configurations.
B. The configuration on a newly added site PE is updated automatically.
C. Provider routers know the customer network topology.
D. The customer specifies the exact site-to-site traffic profile.
E. Routing information is exchanged between the customer router and one or a few PEs.
What must match in the EVPN and L2VPN configuration mode when configuring EVPN native in a router?
A. interface
B. address family
C. bridge domain
D. EVI
An engineer is troubleshooting an EoMPLS circuit on a Cisco IOS XR router interface that removes a VLAN from the distribution layer. Which configuration should the engineer apply in order to accomplish the task?
A. interface GigabitEthernet 0/10.l2transport encapsulation dot1q 10 rewrite ingress tag pop 1 symmetric l2vpn xconnect group 103588 p2p 103588 interface GigabitEthernet 0/10.10 neighbor ipv4 10.10.10.2 pw-id 103588
B. interface GigabitEthernet 0/10.10 encapsulation dot1q 10 rewrite ingress tag pop 1 symmetric l2vpn xconnect group 103588 p2p 103588 interface GigabitEthernet 0/10.10 neighbor ipv4 10.10.10.2 pw-id 103588
C. interface GigabitEthernet 0/10.10 l2transport encapsulation dot1q 10 l2vpn xconnect group 103588 p2p 103588 interface GigabitEthernet 2/10.10 neighbor ipv4 10.10.10.2 pw-id 103588
D. interface GigabitEthernet 0/10.10 l2transport encapsulation dot1q 10 rewrite ingress tag translate 1-to-1 dot1ad 10 symmetric l2vpn xconnect group 103588 p2p 103588 interface GigabitEthernet 0/10.10 neighbor ipv4 10.10.10.2 pw-id 103588
Refer to the exhibit. Which statement describes the result of this configuration?
A. R1 redistributes BGP routes into the OSPF process of VRF custabc as E1 routes.
B. R1 redistributes BGP routes into the OSPF process of VRF custabc as E2 routes.
C. R1 mutually redistributes routes between BGP 65001 and the OSPF process of VRF custabc.
D. R1 redistributes BGP routes into the OSPF process of VRF custabc as OIA routes.
Refer to the exhibit. Which statement about this command is true?
A. It must be configured on each PE router to enable the PE routers to receive multicast traffic for this particular MVRF.
B. It is used to set the designated router on a link using PIM-SM.
C. It must be configured on the PE and CE router to enable MP-BGP to send labels for CSC.
D. It is used to set the router that will server as the root bridge for STP.
Refer to the exhibit:
A network engineer is implementing an OSPF configuration Based on the output, which statement is true?
A. In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.
B. OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface Fastfc.thernet0/0
C. OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.
D. IPv6 routing not enabled" is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway
Refer to the exhibit.
Refer to the exhibit Router 1 is a P router in the ISP MPLS core A connected P router cannot generate an MPLS label for the router 1 loopback0 interface Which action resolves this issue?
A. The loopback0 interface must be in OSPF area 0.
B. The network statement under the routing process must have a wildcard mask of 0 0.0 255.
C. The OSPF network type must be changed on loopback0 to point-to-point
D. A static route to null 0 must be added for the loopback interface and then static routes must be redistributed into OSPF
