DRAG DROP
Refer to the exhibit. Drag and drop the subnets and flags from the left into the External Network Instance Profile policies on the right to create a setup that advertises only 10.10.0.0/24 and 10.10.1.0/24 prefixes in VRF1 and establishes connectivity between VRFs. Not all options are used.
Select and Place:
DRAG DROP
An engineer deploys a Cisco ACI Multi-Site Orchestrator for the first time. Drag and drop the actions from the left into the steps on the right to add a site and deploy new Cisco ACI objects to the fabric. Not all actions are used.
Select and Place:
Refer to the exhibit. What must be configured to allow the PBR node (LB-int) to monitor the availability of the endpoint that is in the EPG server?
A. Endpoint Dataplane Learning
B. Unicast Route disabled for client and server bridge domains
C. PBR node tracking
D. Direct Connect in the service graph template
An engineer must limit local and remote endpoint learning to the bridge domain subnet. Which action should be taken inside the Cisco APIC?
A. Disable Remote EP Learn
B. Enable Enforce Subnet Check
C. Disable Endpoint Dataplane Learning
D. Enable Limit IP Learning to Subnet
Refer to the exhibit. Two application profiles are configured in the same tenant and different VRFs. Which contract scope is configured to allow communication between the two application profiles?
A. global
B. VRF
C. application
D. tenant
Which two components must be configured as stretched to establish intra-VRF communication between two EPGs that are deployed in different sites and different bridge domains? (Choose two.)
A. contract
B. tenant
C. application profile
D. bridge domain
E. EPG
Refer to the exhibit. Which configuration must be implemented on L3Out EBGP to advertise out of the fabric 172.16.2.0/24 network that is learned from L3Out OSPF?
A. Option A
B. Option B
C. Option C
D. Option D
An engineer creates the objects that must be deployed at each site in Cisco ACI Multi-Site Orchestrator. Which action should be taken before the schema can be associated with the newly configured site?
A. Attach the templates to the newly configured site
B. Configure a provider for the Cisco ACI Multi-Site Orchestrator
C. Import existing policies from an existing tenant to Cisco ACI Multi-Site Orchestrator
D. Configure the Infra Site-Specific Settings
Refer to the exhibit. The client endpoint uses the load-balancer VIP as the destination address to send traffic to the server endpoint. If the load balancer does not do source NAT, which set of configurations must be applied on Cisco ACI to allow only the return traffic to be redirected to the service node?
A. 1. Create a contract with a filter matching “IP” only
2.
Create a L4-L7 device, function type “GoTo”
3.
Create a L4-L7 Policy-Based Redirect Policy with the L3 Destination set to the load-balancer inside IP/MAC
4.
Create a service graph template that references the previously created contract and L4-L7 device
5.
Apply the service graph template. Select “L3 Destination” and reference L4-L7 Policy-Based Redirect Policy on the provider connector only
B. 1. Create a contract linked to the common/default filter
2.
Create a L4-L7 device, function type “GoThrough”
3.
Create a L4-L7 Policy-Based Redirect Policy with the L3 Destination set to the load-balancer inside IP/MAC
4.
Create a service graph template that references the previously created contract and L4-L7 device
5.
Apply the service graph template. Select “L3 Destination” and reference L4-L7 Policy-Based Redirect Policy on the consumer and provider connector
C. 1. Create a contract linked to the common/default filter
2.
Create a L4-L7 device, function type “GoTo”
3.
Create a L4-L7 Policy-Based Redirect Policy with “Anycast Endpoint” enabled and the L3 Destination set to the load-balancer inside IP/MAC
4.
Create a service graph template that references the previously created contract and L4-L7 device
5.
Apply the service graph template. Select “L3 Destination” and reference L4-L7 Policy-Based Redirect Policy on the consumer connector only
D. 1. Create a contract with a filter matching “IP” only
2.
Create a L4-L7 device, function type “GoThrough”
3.
Create a L4-L7 Policy-Based Redirect Policy with “Anycast Endpoint” enabled and the L3 Destination set to the load-balancer inside IP/MAC
4.
Create a service graph template that references the previously created contract and L4-L7 device
5.
Apply the service graph template. Select “L3 Destination” and reference L4-L7 Policy-Based Redirect Policy on the consumer and provider
Which action must be taken to connect two nonsilient servers in active/standby mode to two ACI leaves?
A. Implement a virtual PortChannel on ACI leaves
B. Enable ARP flooding for the bridge domain if the MAC address of the active interface changes after NIC failover
C. Configure ARP flooding for the bridge domain if the MAC address of the active interface stays identical after a NIC failover
D. Disable dataplane learning to avoid endpoint flapping
