Review the output of the command shown in the exhibit. Which command is used to generate these results and what does it tell you?
A. swversion displays the Session Manager Release information.
B. statapp displays the current status of the Session Manager services.
C. initDRS displays the Session Manager Node registration and data replication.
D. traceSM displays a ladder trace of the SIP requests going in and out of the Session Manager.
E. smconfig displays the network information and status the Session Manager.
While reviewing the session Manager logs, you notice a log entry that describes that state of an entity "down". Later, you check the logs and notice another log entry that reports the same entity is "partially up". Which troubleshooting procedure will help you to isolate and identify the Entity problem?
A. Run traceSM to capture SIP INVITE message from the entity to determine if there is a display in the network.
B. Run SIP monitoring diagnostics along with ICMP ping to the Entity to verify its connectivity.
C. Run traceSM100 to capture SIP MONITOR message from the entity to determine if there is a delay in the network.
D. Run SIP Entity Performance on the Entity to determine id SIP OPTIONS messages are being blocked on the network.
A technician wants to schedule a bulk operation to take place at a convenient time in the future. What are two methods for scheduling bulk operations? (Choose two.)
A. # Sh exportUpmUsers.sh -u admin -p adminl23 -t 2013:05:01:12:00:00
B. # sh exportUpmUsers.sh -u admin -p adminl23 -d 2013:05:01:12:00:00
C. Navigate to Users > User Management, click 'More Options' and select 'Import Users'. Choose 'schedule' in the options.
D. Navigate to Users > User Management, click 'More Options' and select 'Export Users'. Choose 'schedule' in the options.
Which two wildcard characters does Session Manager allow to specify a location pattern? (Choose two).
A. "%" (percentage)
B. "$" (dollar)
C. "*" (star/asterisk)
D. "#" (pound/hex)
E. "X"
A new feature server has been deployed in the network. The feature server must be applied to all calls made and received by the user. A technician has been asked to make the necessary arrangements. After adding a SIP Entity and Entity Link, which sequence describes the next steps that should be taken?
A. Navigate to the user's User Profile and open the Session Manager Profile. From the Originating Application Sequence drop down list, select the new Application Sequence. Repeat for the Terminating Application Sequence drop down list. Mark them both as being Mandatory.
B. Define the new feature as an Application. Add the Application to an Application Sequence. Mark the Application Sequence as Mandatory. Add the Application Sequence to user's User Profile.
C. Create a new Application Sequence or edit one that already exists. Add details of the new feature to the Application Sequence. Mark the new feature as being mandatory. Apply the Application Sequence to user's Originating and Terminating Application Sequences In their Session Manager Profile.
D. Define a new Application that details the new feature. Add the new Application to an Application Sequence. Mark the new feature as being mandatory. Apply the Application Sequence to both Originating and Terminating Application Sequences in the user's Session Manager Profile.
A routing policy administrator needs to create a policy that enables Session Manager to route to different destination based on different conditions. Time of day is one such condition. Which two Parameters may also be used by Session Manager when selecting the applicable routing policy? (Choose two.)
A. the location of the calling party
B. the registration state of the destination
C. the SIP domain of the called party
D. the origination or termination application sequences that will be applied to call, ignoring what the applications themselves may do
Users between four customer sites are reporting frequent problems placing and receiving calls. In trying to identify the issue, you check the Bandwidth Usage between Session Manager Locations and get an error message, "Unable to access status information for SM1 ?cannot connect to server, internal error". Which item is most likely the cause of this error?
A. There is limited bandwidth between the locations.
B. The Session Manager Service State was set to deny new service.
C. The System Manager cannot communicate with the Session Manager because of a network issue.
D. The Session Manager is processing high volume of calls and is causing inter-SM server connectivity problems.
When defining a SIP Entity of type "Session Manager", what should be placed in the FQDN or IP Address field?
A. Security Module IP address (eth2)
B. System Manager IP address (eth0)
C. Session Manager Management IP address (eth0)
D. System Platform web console IP address (eth2)
All administrator is instructed to add a Regular Expression to Routing Policy that matches all dialed numbers being with a 14 and 15 (for example 14000 and 15999, but not 24000). Which two regular expression patterns will match against such numbers? (Choose Two)
A. sip: [1\]{1}4*5*[0-9\]{3}
B. sip: [1\]{1}[4-5\]{1}[0-9][3]
C. sip: 1[4-5\][0-9\][0-9\]
D. sip: 1(4/5){1}[0-9]*
Session Manager has a routing policy that routes calls made to any number beginning with '100' to SIP Entity X. However, 'sip.-1001avaya.com' is the SIP communication profile address of user Y. User Y is not currently registered (signed in) with Session Manager. What will happen if Session Manager receives a call addressed to 'sip.-1001avaya.com' and why?
A. It depends on the time ranges of the policy. If the call is placed inside a defined time range for the policy, the call will be routed to destination X. If not, then Session Manager will attempt to route the call to user Y. Since Y is not registered, the call will timeout, and the call will fail.
B. Since user Y is not currently registered, the call will be handled by the routing policy. If the call is placed during a time range specified by the policy, then the call will be routed to destination
X. If not, then the call will fail.
C. Since the destination URI matches a communication profile SIP handle, Session Manager will not use the routing policy in handling the call. The call will fail since user Y is not currently registered.
D. Since the destination URI matches a routing policy dial pattern, Session Manager will give no consideration to the user Y registration status. If the call is made during a time range for the policy, the policy will be applied and the can will be routed to destination X. If not, then the original URI of 'sip.-1001avaya.com' will be used as the destination to which Session Manager will route the call.
