When configuring a new Ethernet Routing Switch (ERS) 8000 using the default interface, the attempt to load an ACLI configuration fails because the default
interface is the CLI.
How is the ACLI interface obtained?
A. Change the interface type in the config.cfg file.
B. Change the ACLI boot flag and save the boot configuration file.
C. Exit the CLI and choose ACLI at the interface manager prompt.
D. Use the abort command and enter `no' at the default interface.
By default the ERS 8000 is configured for warm standby. After installation of a new ERS solution with dual CPUs, which three actions need to be Perform on the ERS configuration to ensure high availability mode is enabled and will function correctly? (Choose three)
A. Set the high availability CPU boot flag to true.
B. Set the warm standby CPU hoot flag to false.
C. Set the save to standby CPU boot flag to true.
D. Save the boot.cfg conflg file and reset the switch to activate the changes.
E. Install the high availability license file.
Which statement describes a step in provisioning SPBM in an enterprise network?
A. Configure IP addresses on the core links.
B. Enable SPBM and IS-IS globally on all nodes and on the core facing links.
C. Configure the MAC table.
D. Configure L2 and L3 VSNs on the core SPBM nodes.
When multiple VLANs are used, Dynamic Host Control Protocol (DHCP) relay is required to get the DHCP information from the end user VLAN DHCP server. Which statement about how to enable DHCP relay is true?
A. The physical VLAN IP address is configured as the DHCP relay agent on each VLAN requiring a DHCP relay.
B. The IP address of the DHCP server is configured as the relay agent globally on all switches that do not directly attach to the DHCP server.
C. The MAC address of the DHCP server configured as the DHCP relay agent on each VLAN requiring the DHCP relay agent.
D. The DHCP relay is configured globally and is automatically applied to all VLANs requiring a DHCP relay.
Which two functions describe VPFM? (Choose two.)
A. It is a network health at a glance tool.
B. It can correlate faults, traps, and provide notification.
C. It is another term for the SNM credential.
D. It is a device configuration tool.
The Ethernet Routing Switch (ERS) 8600 supports the feature IP VPN-Lite that does not require the use of an MPLS network. Which function does the ERS 8600 as a Provider Edge (PE) perform for IP VPN-Lite?'
A. The PE uses the Virtual Routing Forwarding (VRF) instances to provide traffic separation.
B. The PE provides route exchange with remote PE devices using OSPF.
C. The PE adds a shim header to the Ethernet header specifying which network the packet is crossing.
D. The PE incorporates Label Distribution Protocol across the core network to connect remote PE devices.
When configuring an Ethernet Routing Switch (ERS) 8600 redundant Installation for warm standby, which protocol is used to give the fastest recalculation of large layer 3 topology by the standby CPU, after a Master CPU failure?
A. STP
B. Rip
C. OSPF
D. BGP
Which statement describe step in provisioning SPBM in an Enterprise network?
A. IP addresses on the core links.
B. Enable SPBM and IS -IS globally on all nodes and on the core facing links.
C. Configure the MAC table.
D. Configure L2 and L3 VSNs on the core SPBM nodes.
A technician is configuring a Link Aggregation connection from a stack of Ethernet Routing Switch (ERS) 5500 lo a core pair of ERS 8600 switches. Which statement about the correct uplink configuration is true?
A. Distribute uplinks across different ERS 5500 switches in the stack.
B. Disable auto negotiation and replace it with VLACP to identify single fiber fault failure
C. Use unique MLT IDS for each stack of edge ERS 5500 switches
D. Enable Spanning Tree Protocol for the MLT when using it with SMLT in the core of the network.
When configuring an Ethernet Routing Switch (ERS) 8600 for Split Multi link Trunking (SMLT). Protection against an edge switch in the factory default condition must be taken into consideration. Which parameter WILL help prevent loops on the SMLT ports?
A. Discard Untagged Frames
B. Discard Looped Frames
C. Spanning Tree Enable
D. LACP Enable
