Which of the following routing protocols are supported on the Alcatel-Lucent 7750 SR to enable constraint-based LSPs? (Choose two)
A. RIPv2-TE
B. CSPF
C. OSPF-TE
D. ISIS-TE
E. RSVP-TE
Which of the following commands is used to display the database containing the OSPF-TE LSAs?
A. show router ospf opaque-database
B. show router ospf database
C. show router ospf opaque-Isa
D. show router ospf te opaque
Which of the following describes what happens when facility backup fast reroute is enabled for a LSP? Choose three answers.
A. Each PLR will signal a bypass tunnel that avoids the next-hop node or link.
B. When a failure occurs, the PLR will push an additional label onto the label stack and start forwarding traffic onto its bypass tunnel.
C. The ingress router will include a RRO object in the path message to indicate the routers that should be PLRs and MPs along the protected path.
D. The ingress router will set the local protection desired flag in the session attribute object of the path message to inform all routers along the protected LSP path to establish bypass tunnels.
E. When the bypass tunnel is in use, the MP will include the RRO object in its PathErr message, with the local protection in use flag set to notify the ingress router that it is using the bypass tunnel.
Which of the following can be used for label signaling and distribution on the Alcatel-Lucent 7750 SR? Choose two answers
A. RSVP-TE
B. TDP
C. LDP
D. ADP
E. MPLS-TE
Click on the exhibit button below.
Consider the output shown; what table is displayed?
A. RIB
B. FIB
C. LIB
D. LFIB
Which of the following about LDP-over-RSVP is TRUE?
A. RSVP LSPs must exist between each PE-ABR pair, or ABR-ABR pair in each area.
B. When LDP-over-RSVP is active, the LDP prefixes are resolved to a physical egress interface.
C. Targeted sessions must exist between all routers along the tunnel path.
D. Link LDP sessions must exist between each ABR-ABR pair in each area.
Click on the exhibit.
All links have 1Gbps unreserved bandwidth initially and Shared Explicit reservation style is used. After the
LSP's primary and standby secondary paths are signaled, how much unreserved bandwidth is left on the links?
A. R1-R2 will have 300Mbps left and R2-R4 will have 400Mbps left.
B. R1-R2 will have 400Mbps left and R2-R4 will have 400Mbps left.
C. R1-R2 will have 600Mbps left and R2-R4 will have 600Mbps left.
D. R1-R2 will have 300Mbps left and R2-R4 will have 600Mbps left.
Which of the following is NOT a characteristic of MPLS?
A. It provides the ability to establish connection oriented paths over a connectionless IP network.
B. It provides a mechanism to engineer network traffic patterns independently of IP routing tables.
C. It will work over most physical layer protocols.
D. It can use GRE tunnels to transport data from many different protocols over an IP network.
Which of the following is NOT required when configuring an LSP with an admin group constraint on an Alcatel-Lucent 7750 SR?
A. Enable traffic engineering on all routers along the LSP path.
B. Enable CSPF on the head-end router.
C. Configure a path definition on all routers along the LSP path.
D. Enable MPLS and RSVP on all routers along the LSP path.
Click on the exhibit.
If the primary path goes down, which secondary LSP path will the head-end router select first?
A. Secondary_Path-1 B. Secondary_Path-2
C. Secondary_Path-3
D. Secondary_Path-4