In a PIM-SM network, which type of node helps to build a tree towards an unknown multicast source?
A. DIS
B. RP
C. DR
D. BSR
-- Exhibit
-- Exhibit -
Click the Exhibit button.
Referring to the exhibit, which LSA type will Router R2 inject into Area 1?
A. Type 3 LSA
B. Type 4 LSA
C. Type 5 LSA
D. Type 7 LSA
-- Exhibit
-- Exhibit -
Click the Exhibit button.
Referring to the exhibit, which two statements are correct? (Choose two.)
A. Traffic destined for R2 will be blackholed.
B. Transit traffic will follow the R1-R2-R4 path.
C. Traffic destined for R2 will reach R2.
D. Transit traffic will follow the R1-R3-R4 path.
-- Exhibit
-- Exhibit -Click the Exhibit button.
R1 is connected to both R2 and R3 and you want to load-balance outbound traffic. You have provided the configuration shown in the exhibit; however, after checking the links you notice that the traffic is not load- balancing.
Which configuration must be added?
A. set protocols bgp group external multihop
B. set protocols bgp group external multipath
C. set protocols bgp group external advertise-external
D. set policy-options policy-statement loadbal then accept
-- Exhibit
-- Exhibit -Click the Exhibit button.
Referring to the exhibit, the RPs are set up for anycast. Multicast traffic is currently flowing from the source to the receivers.
Which statement is true when RP2 goes down?
A. Multicast traffic is interrupted for receiver 2 until RP2 recovers.
B. Receiver 2 needs to rejoin RP1.
C. Multicast traffic flows uninterrupted.
D. RP1 starts sending multicast traffic to receiver 2.
You are asked to set up 802.1X port authentication for all access ports on your EX Series switch. You must ensure that only one user is allowed to authenticate per port and all other attempts are denied.
Which supplicant mode must be used?
A. single mode
B. single-secure mode
C. default mode
D. multiple mode
You are setting up a new switch in your network that is using MSTP. You have configured all access ports as edge ports, and you want to make sure that the access ports can never transition to nonedge ports. How can you meet this requirement?
A. Configure the interfaces as shared.
B. Configure the hello-time option as zero.
C. Configure the interfaces as a no-root-port.
D. Configure bpdu-block-on-edge.
Which statement describes 802 1x supplicant single modes?
A. 802 1x supplicant single mode permit access for the first supplicant, all other applicants that connect to the port are allowed full access without further authentication
B. 802 1x supplicant single mode allows all supplicant to connect to the port,each supplicant is authenticated individually
C. 802 1x supplicant single mode permits access for a single supplicant,all other supplicants attempting to connect through the same port are denied access
D. 802 1x supplicant single mode allows only one supplicant to connect to the port,no other supplicant is allowed to connect until the first supplicant disconnects
You manage your company's enterprise network using EX series switches. Your company wants to use Q in Q tunneling to correct remote customer sites together, which statement is correct about the scenario?
A. you must enable L2PT to tunnel layer 2 protocol traffic
B. the outside layer 2 frame is popped by the penultimate switch
C. customer traffic is tunneled through the network using the C-VLAN-ID
D. the default Ethernet type value is 0x9100
You are a service provider and have multiple customers in a building. You are installing a new switch that can host all of your customers. However, you would like to ensure that one customer cannot see or broadcast to another customer. You
would also like to have them use a common gateway IP address from the building.
What of following should be used to provide this access?
A. Layer 2 tunneling
B. VLAN
C. filter-based VLAN
D. private VLAN
