Click the Exhibit button.
In the exhibit, Area 1 is a not-so-stubby area. Three networks are redistributed into Area 1 on R2. You must summarize the redistributed network addresses in Area 1 so that only one network prefix is re-advertised into Area 0. You must also summarize the loopback addresses of R1 and R2 into a single address in Area 0.Which configuration sample on R3 and R5 will complete this task?
A. Option A
B. Option B
C. Option C
D. Option D
Click the Exhibit button.
In the exhibit, R1 has a loopback address of 192.168.1.1. Its loopback interface is included in OSPF Area 1.Which two statements are true? (Choose two.)
A. R1 will advertise the loopback address in a Type 1 LSA.
B. R1 will advertise the loopback address in a Type 3 LSA.
C. Area 0 will see the loopback address in a Type 1 LSA.
D. Area 0 will see the loopback address in a Type 3 LSA.
Click the Exhibit button.
You are provisioning a full-mesh BGP Layer 2 VPN for Customer A. The customer has four remote sites in their network. Using best practices, you assigned interface unit numbers matching the assigned VLAN numbers. Which Layer 2 VPN configuration is correct for PE2?
A. Option A
B. Option B
C. Option C
D. Option D
You are evaluating a routing policy for an ISP and you find the ^42+ .* (23|9)$ regular expression. Which three AS paths match the regular expression? (Choose three.)
A. 42 42 42 42 9
B. 42 42 23 500
C. 42 42 42 60 9
D. 42 60 23 9 42
E. 42 69 500 23
Click the Exhibit button.
You are asked to configure an OSPF network based on the topology shown in the exhibit. Area 1 must not
receive Type 5 LSAs from the backbone, but must be capable of containing ASBRs.
What will accomplish this?
A. Area 1 should be configured as a stub area, which by default meets the network's requirements.
B. R3 should be configured with no-externals for Area 1, which will suppress Type 5 announcements.
C. R3 should be configured with no-summaries for Area 1, which will suppress Type 5 announcements.
D. Area 1 should be configured as an NSSA, which by default meets the network's requirements.
Click the Exhibit button.
What is the significance of RIB groups, as shown in the exhibit?
A. RIB groups alter the multicast RPF check table to inet.0.
B. RIB groups alter the multicast RPF check table to inet.2.
C. RIB groups alter the multicast RPF check table to inet.4.
D. RIB groups alter the multicast RPF check table to inet.3.
Click the Exhibit button.
After adding Customer C to your Layer 3 VPN, you must validate that PE2 is receiving VPN routes for all customers attached to PE1, as shown in the exhibit. Which operational command displays this information?
A. show route instance
B. show route summary
C. show route table bgp.l3vpn.0
D. show route table customer-c.inet.0
Click the Exhibit button.
You work for ISP A, as shown in the exhibit, and must configure R1 to use load balancing across both available links for all routes to ISP B's network. You start by configuring this policy:
policy-statement load-balance { then {
load-balance per-packet; } }
Which two commands do you use to finish the configuration? (Choose two.)
A. set protocols bgp group isp-b multihop
B. set routing-options forwarding-table export load-balance
C. set routing-options forwarding-table import load-balance
D. set protocols bgp group isp-b multipath
You are configuring a Layer 2 circuit. Which two configuration steps are required? (Choose two.)
A. Configure LDP on the interfaces between PE and CE routers.
B. Configure circuit or translational cross-connects between PE routers and between PE and P routers.
C. Configure circuit or translational cross-connects between PE and CE routers.
D. Configure LDP on the interfaces between PE routers and between PE and P routers.
-- Exhibit
-- Exhibit -Click the Exhibit button.
You are the administrator for AS 1111 and you want to inform the neighboring AS to use router A2 as the
ingress path into your local AS.
Referring to the exhibit, which policy statement action for the export policy on A2 will perform this task?
A. set policy-options policy-statement export term 10 then metric 120
B. set policy-options policy-statement export term 10 then external
C. set policy-options policy-statement export term 10 then metric 25
D. set policy-options policy-statement export term 10 then priority low
