An engineer receives two new I/O Aggregators (IOAs) in default mode. The engineer needs to make sure the uplink ports only pass tagged traffic in VLANs 100 and 200.
Which option allows the engineer to accomplish this task?
A. Set the uplink ports to hybrid ports
B. Change the IOA mode to Programmable MUX mode
C. Remove all untagged VLANs from the uplinkports
D. Tag only VLAN 100 and 200 on the uplink ports
Refer to the exhibit.
An engineer sets up FCoE boot on their server. The server fails during post.
What needs to be added to the NIC settings/option ROM to make booting successful?
A. The WWN of the FIP snooping bridge
B. The WWN of the storage target
C. The WWN of the FC port ID
D. The WWN of the fibre channel switch
An engineer is installing 10Gb modules into a pair of MXL switches. Which cable is correct for this installation?
D)
A. Exhibit A
B. Exhibit B
C. Exhibit C
D. Exhibit D
Refer to the exhibit.
An engineer needs to configure iSCSI boot on a blade.
iSCSI boot is NOT working.
Which two steps should the engineer take to fix the issue? (Choose two.)
A. Verify the IP address of the target and initiator
B. Update the DNS server entries on the initiator
C. Change the IQN of the initiator
D. Validate default gateway settings on the initiator
E. Modify the boot LUN ID on the target
Refer to the exhibit.
An engineer receives a pair of the modules shown to install in a pair of MXL switches.
Which cables does the engineer need for this module?
A. OM4 MTP Crossover Fiber Cable (optics required)
B. SFP+ to SFP+, 10GbE, Copper Twinax Direct Attach
C. QSFP+ to QSFP+, 40GbE Passive Copper Direct Attach.
D. Cat6A Snagless Unshielded (UTP) Network Patch Cable
An engineer needs to connect ports 49 and 53 on an MXL to a top of rack (ToR) switch in an LACP port channel. The ToR switch has ports 46 and 60 configured in port channel 100.
Which configuration will successfully bring up the port channel on the MXL?
A. interface Port-channel 1switchportinterface range fortyGigE 0/49, fortyGigE 0/53port- channel-protocol LACPport-channel 1 mode active
B. interface Port-channel 100channel member fortyGigE 0/49, firtyGigE 0/53switchportinterface range fortyGigE 0/49, fortyGigE 0/53port-channel 100 mode active
C. interface Port-channel 100channel member fortyGigE 0/49, fortyGigE 0/53switchportinterface range fortyGigE 0/49, fortyGigE 0/60lacp mode active
D. interface Port-channel 1switchportinterface range fortyGigE 0/46, fortyGigE 0/60port- channel-protocol LACPport-channel 1 mode active
An engineer is configuring a new FD332 storage sled into an existing chassis in SLOT 3. The engineer is unable to create any RAID arrays although the drives are detected.
Which task should be completed to create RAID volumes?
A. Import the PERC license into the iDRAC
B. Configure RAID in Ctrl+R
C. Change storage mode to joined in the CMC
D. Enable the PERC in storage sled.
A VRTX has the following physical disks:
-8 300 GB SSDs
-10 300 GB 15,000 rpm HDDs
An engineer needs to create two virtual disks for a file server: a system volume and a data volume.
The customer wants to maximize performance of the system volume and maximize redundancy of the data
volume.
The customer also wants both virtual disks to survive one drive failure without the customer's intervention.
Which option is most appropriate to meet the requirements?
A. System: 7 SSDs in RAID 0Data: 9 HDDs in RAID 6One SSD and one HDD as dedicated hot spares for each volume
B. System: 8 SSDs in RAID 10Data: 8 HDDs in RAID 6Two HDDs as dedicated hot spares for each volume
C. System: 6 SSDs in RAID 10Data: 10 HDDs in RAID 6Two SSDs as dedicated hot spares for each volume
D. System: 7 SSDs in RAID 5Data: 9 HDDs in RAID 6One SSD and one HDD as dedicated hot spares for each volume
A password to the CMC root account on an M1000e server chassis has been misplaced. What should be done to restore administrative access to the CMC?
A. Reset root password using the PASSWORD_RSET jumper
B. Issue password reset from a connected blade's iDRAC
C. Call Dell tech support and ask to reset CMC password via SupportAssist
D. Access CMC through serial console and issue theenable secretcommand
An engineer needs to connect two MXL switches that both have SFP+ add-on module.
Which cable will complete this task?
A
A. Exhibit A
B. Exhibit B
C. Exhibit C
D. Exhibit D
