An administrator just finished configuring a Dell EMC N-Series switch. After rebooting the switch, the administrator notices that all the configuration settings just entered are gone.
Which command did the administrator fail to enter?
A. Copy running-config startup-config
B. Copy running-config backup-config
C. Copy startup-config backup-config
D. Copy startup-config running-config
What is the recommended maximum number of routers, per area, when using OSPF?
A. 50
B. 100
C. 200 D. 255
When configuring a Dell EMC N-Series switch for voice traffic, which settings are needed?
A. Enable voice VLAN Set each-interface to LLDP share all VoIP related parameters Set switchport mode to general
B. Create a VLAN for voice Set each interface to ISDP share all VoIP related parameters Set switchport mode to general
C. Enable voice VLAN Set each interface to LLDP share all VoIP related parameters Set switchport mode to hybrid
D. Enable voice VLAN Set each interface to ISDP share all VoIP related parameters Set switchport mode to general
The exhibit represents a topology with all Dell EMC N4000 Series switches with RSTP enabled. In addition, the switches are using the default configuration on all ports and protocols. Which port number will be blocked by spanning tree?
A. Te 1/0/3
B. Te 1/0/4
C. Te 1/0/5
D. Te 1/0/6
Which ports on a spanning tree root switch are always forwarding?
A. Alternate ports
B. Designated ports
C. Backup ports
D. Root ports
To which destination MAC address are MLAG peer-keepalive packets sent?
A. 01:00:B5:00:00:00
B. 01:00:C5:00:00:00
C. B5:00:01:00:00:00
D. C5:00:01:00:00:00
A network administrator has configured a 4-port port-channel between two Dell EMC Campus networking switches. The physical interfaces show as administratively up and operationally up on both switches. However, the port-channel shows as operationally up on Switch A and operationally down on Switch B.
What is a potential reason for the inconsistent port-channel state?
A. Switch A is configured to use dynamic port-channels and Switch B is configured to use static port-channels
B. Ports in the port-channel on Switch A are all the same speed but the ports in the port-channel on Switch B are a mix of speeds
C. Switch A is configured using channel-group # mode on and Switch B is configured using channel-group # mode auto
D. N-Series supports a maximum number of physical interfaces that can be included in port-channels on a per-device basis
Two switches are part of the same VRRP group with the following priorities configured:
Switch1: Priority 110
Switch2: Priority 90
Switch2 is required to be the Master if interface GigabitEthernet 0/2 on Switch1 fails.
Which configuration should be part of the setup?
A. Switch1(conf-if-vlan10)# vrrp 1 track interface vlan 20 decrement 100 Switch1(conf-if-vlan10)# no vrrp 1 preempt
B. Switch2(conf-if-vlan10)# vrrp 1 track interface vlan 20 decrement 100 Switch2(conf-if-vlan10)# no vrrp 1 preempt
C. Switch1(conf-if-vlan10)# vrrp 1 track interface vlan 20 decrement 100 Switch1(conf-if-vlan10)# vrrp 1 preempt
D. Switch2(conf-if-vlan10)# vrrp 1 track interface vlan 20 decrement 100 Switch2(conf-if-vlan10)# vrrp 1 preempt
A Dell EMC N-Series switch is configured to uplink to a customer switch using two separate 4-port port-channels configured as trunks. Both switches are configured with 16 VLANs and RSTP.
How will VLAN traffic be distributed across the port-channels?
A. All VLANs are allowed across a single port-channel
B. A single VLAN is allowed across each port-channel
C. All VLANs are allowed across both port-channels
D. Eight VLANs are allowed across each port-channel
N4032F#show interfaces status
N4032F#show interfaces port-channel 1
Hash Algorithm Type 1 - Source MAC, VLAN, EtherType, source module and port Id 2 - Destination MAC, VLAN, EtherType, source module and port Id 3 - Source IP and source TCP/UDP port 4 - Destination IP and destination TCP/UDP port 5 - Source/Destination MAC, VLAN, EtherType, source MODID/port 6 - Source/Destination IP and source/destination TCP/UDP port 7 - Enhanced hashing mode
N4032F#
A Dell EMC N-Series switch has been configured with a 2-member port-channel; however, only one link is currently active.
Based on the exhibit, why is only one link active?
A. Minimum links value for Po1 is set to "1"
B. Hash algorithm is configured for active-passive
C. Te1/0/6 interface is administratively disabled
D. Speed setting is different between ports
