What is one difference between Network Segment-based discovery and ARP-based discovery on HP Intelligent Management Center (IMC)?
A. With Network Segment-based discovery, IMC can discover multiple devices. With ARP- based discovery, IMC can only discover one device; the administrator must re-run ARP- based discovery to discover a second device.
B. With Network Segment-based discovery, network device login settings must match login settings on IMC. With ARP-based discovery, only ARP settings must match.
C. With Network Segment-based discovery, network device SNMP settings must match SNMP settings on IMC. With ARP-based discovery, only ARP settings must match.
D. With Network Segment-based discovery, the administrator enters a range of IP addresses to discover. With ARP-based discovery, the administrator enters one seed IP address, and IMC dynamically learns more IP addresses to discover.
Refer to the Exhibit.
Examine the output from the Comware command shown in the exhibit. Based on the flag of ACDEF, what is the status of the aggregated link?
A. Static LACP link aggregation is configured, and the aggregated link is operational with load sharing not being performed.
B. Static link aggregation is configured, and the aggregated link is operational with load sharing being performed.
C. Static LACP link aggregation is configured, and the aggregated link is operational with load sharing being performed.
D. Static link aggregation is configured, and the aggregated link is operational with load sharing not being performed.
A company wants to implement HP Intelligent Resilient Framework (IRF) at the access layer. Which switches could they use?
A. two HP 5500 HI Series switches
B. one HP 5412R zl2 Series switch and one HP 5800 Series switch
C. one HP 5800 Series switch and one HP 5500 Series switch
D. two HP 5406R zl2 Series switches
A network administrator enters this command on an HP Comware switch:
In interactive mode, the administrator is prompted to save to a file named config.cfg and confirms the save. What is the effect of these actions?
A. The current configuration is saved to config.cfg on a TFTP server but is not used for the startup-config.
B. The startup-config, rather than the correct configuration, is saved to config.cfg on a TFTP server.
C. The current configuration is saved to config.cfg in the flash but is not used for the startup-config.
D. The current configuration is saved to config.cfg in the flash and is used for the startup- config.
Which statement is true about the default configuration on an HP ProVision switch?
A. Spanning tree is disabled.
B. LACP is used when a BAGG interface is created.
C. IRF is enabled.
D. RSTP is the default spanning tree mode.
What is one reason to access the extended boot menu on an HP Cornware switch?
A. To access the switch CLI when you have forgotten the password
B. To set up the switch to be managed by HP Intelligent Management Center (IMC).
C. To configure the switch initial IP address settings
D. To configure the switch to implement Intelligent Resilient Framework (IRF)
A network administrator wants an HP switch to use an IP address that is always up for its Open Shortest Path First (OSPF) router ID. Which address meets this requirement?
A. An IP address configured as the global management address
B. An IP address on the interface for the default VLAN, which is typically VLAN
C. An IP address on the VLAN 1 interface
D. An IP address on a loopback interface
What is one feature that MSTP has that RSTP does not have?
A. load-sharing on redundant links
B. alternate root ports
C. multiple designated ports per segment
D. one set of BPDUs per VLAN
A company has a network comprised of HP Comware and ProVision switches. A network administrator purchases HP Intelligent Management Center (IMC) to manage the switches in this network. Which step must the administrator perform on the Comware switches but not on the ProVision switches?
A. Configure SNMP traps.
B. Configure VTY interface authentication.
C. Define SNMPv2 community strings or SNMPv3 groups and users.
D. Configure telnet or SSH.
Exhibit1.
Exhibit 2
A network administrator wants to create a backup IP route to 10.1.20.0/24 on Switch-1. The backup route should use Link 2, and it should only be used if Link 1 is down. What is the correct setup to accomplish this?
A. an IP route through 10.0.2.2 with administrative distance 1
B. an IP route through 10.1.20.1 with administrative distance 1
C. an IP route through 10.0.2.2 with administrative distance 10
D. an IP route through 10.1.20.1 with administrative distance 10
