Which command can a network administrator execute on an HP Comware switch to manage configuration files?
A. delete
B. startup-default
C. write file
D. write memory
What is true about the community string used for SNMPv1 and SNMPv2c?
A. The community string encrypts the SNMP message, but does not hash it, providing for data privacy.
B. The community string hashes the SNMP message, but does not encrypt it, providing for data integrity.
C. The community string encrypts and hashes the SNMP message, providing for data integrity and privacy.
D. The community string is like a password transmitted in cleartext, providing no data integrity or privacy.
Refer to the exhibit.
The switches in the exhibit are all HP Comware switches that run Multiple Spanning Tree Protocol (MSTP).
The network administrator wants to ensure that each switch-to-switch link is in its own subnet. The administrator also wants to make sure that all of the links are available for routing during normal operation. How should the administrator configure the physical switch-to-switch interfaces to accomplish these goals?
A. Configure them as trunk ports that permit VLANs 10 and 20.
B. Configure them as any type of port, and make sure spanning tree is enabled on them.
C. Configure them as route-mode ports.
D. Configure them as hybrid ports that carry VLAN 10 and 20 as untagged.
Which statement is true about the default configuration on an HP ProVision switch?
A. Spanning tree is disabled.
B. LACP is used when a BAGG interface is created.
C. IRF is enabled.
D. RSTP is the default spanning tree mode.
Refer to the exhibit.
The topology shown on the left of the exhibit illustrates a traditional three-tier architecture. Which technology allows a company to simplify their network with a two-tier topology as illustrated on the right of the exhibit.
A. Intelligent Resilient Framework
B. Software-defined Networking
C. Multiple Spanning Tree Protocol
D. Equal Cost Multi-Pathing
Refer to the exhibit.
What does the output indicate about GE1/0/1?
A. The interface accepts untagged traffic, which it assigns to VLAN 1. It drops traffic that is tagged for VLANs 1, 10, and 20.
B. The interface accepts untagged traffic, which it assigns to VLAN 1. It also accepts traffic that is tagged for VLANs 10 and 20.
C. The interface accepts untagged traffic, which it assigns to VLAN 1. It accepts traffic that is tagged for any VLAN between 10 and 20.
D. The interface does not accept untagged traffic. It accepts traffic that is tagged for VLANs 1, 10, and 20.
A customer has an HP ProVision switch capable of Layer 3 forwarding: however, Layer 3 forwarding is disabled. The switch has an IP address in the management VLAN, where the default gateway is 10.1.1.1, which ProVision command should the network administrator use so the ProVision switch can access the Intelligent Management Center (IMC) server in a different VLAN?
A. IP default-gateway 10.1.1.1
B. IP route 0.0.0.0 255.255.255.255 10.1.1.1
C. Default-route 10.1.1.1
D. IP route 0.0.0.0.0.0.0.0 10.1.1.1
Which settings enable a network administrator to use terminal emulation software to interface with an HP Comware switch's auxiliary port?
A. 9600 bps, 7 data bits, 1 stop bit, no parity, flow control
B. 14,200 bps, 8 data bits, 1 stop bit, parity, flow control
C. 9600 bps, 8 data bits, 1 stop bit, no parity, no flow control
D. 9600 bps, 8 data bits, 1 stop bit, parity, flow control
In the HP Software-defined Networking (SDN) architecture, what connects the Application layer to the physical device or Infrastructure layer?
A. HP Network Automation
B. HP SDN Controller
C. HP IMC Virtual Network Manager (VNM)
D. HP IMC SDN Manager
Which statement is true concerning spanning tree protocols and HP switches?
A. ProVision switches use non-standard default cost values
B. Comware switches have spanning tree enabled, by default
C. ProVision switches, by default, auto-sense edge ports
D. Comware switches use their serial number as the switch identifier in the bridge ID
