HPE0-V14 Online Practice Questions and Answers

DRAG DROP

Match each characteristic to the correct storage type.

Select and Place:

DRAG DROP Match the feature to the lowest iLO5 license in which it is available

Select and Place:

Read the question, and then refer to the exhibit.

display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: Administratively DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: TenGigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK_SFP_PLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10, 20 VLAN permitted: 10, 20 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 18 seconds Last clearing of counters: Never Peak input rate: 78 bytes/sec, at 2011-03-31 04:55:57 Peak output rate: 15 bytes/sec, at 2011-03-30 23:00:57 Last 300 second input: 0 packets/sec 67 bytes/sec -% Last 300 second output: 0 packets/sec 14 bytes/sec -% Input (total): 62670 packets, 8565340 bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input (normal): 62670 packets, -bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, -overruns, 0 aborts ?ignored, -parity errors Output (total): 3707 packets, 1294835 bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output (normal): 3707 packets, -bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output: 0 output errors, -underruns, -buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, -no carrier

A customer added a new switch to their network. They connected it using interface Ten-GigabitEthernet 1/0/1. They are using VLAN 10 and 20 for the devices in their network.

The new switch was fully operational. Then, the customer experienced a power failure later that day and could not reach any device on the new switch after the power returned.

From the output in the exhibit, would could be the issue?

A. The interface loopback is not set.

B. The interface link-speed and duplex are unknown.

C. The interface is administratively down.

D. The interface is configured for a PVID of VLAN 1.

A customer needs to update a server's firmware using the latest Support Pack for ProLiant (SPP). They use a bootable USB flash drive to do so, and they select Interactive Mode on boot. Once the device boots, they are unsure how to proceed and ask for your assistance.

What can you tell them to do to easily update the firmware?

A. Download a new version of Smart Update Manager.

B. From Interactive mode, select the "Force Firmware" option.

C. Reboot the server with the flash drive and leave in default mode.

D. Run interactive mode from the Operating System instead.

Exhibit:

Which HPE ProLiant Server meets the customer's requirements?

Which HPE ProLiant Server meets the customer's requirements?

A. Option A

B. Option B

C. Option C

D. Option D

Refer to the exhibit.

An administrator connected a hypervisor to interface Ten-GigabitEthernet1/0/1 in a switch. The administrator created virtual machines in VLAN 10 and 20 on the hypervisor. VLAN 10 is configured to be tagged, and VLAN 20 is configured to

be untagged on the hypervisor.

The administrator found that all the virtual machines in VLAN 20 can communicate with each other, but not with any virtual machines on VLAN 20 external to the hypervisor.

Given the output in the exhibit, customer needs a new environment to support an ERP system. The sizing information you received shows the following

A. Permit VLAN 1 on the interface.

B. Configure the PVID of the interface to be VLAN 20.

C. Configure the interface as an access port.

D. Configure the interface as an IRF port.check

Which HPE remote management tool offers simplified warranty and contract case management?

A. HPE InfoSight

B. HPE Insight Online

C. HPE iLO Advanced

D. HPE Smart Update Manager

A customer needs an HPE Nimble storage solution with 100TB capacity. They want to be able to add more disk capacity if needed Which HPE tool can help you validate the proposed storage solution and that it is supported by HPE?

A. HPE Ninjastars

B. HPE One Config Advanced

C. HPE Storage Sizing Tool

D. HPE SPOCK

A customer needs to share files among their Linux-based servers in a cost effective manner. The customer is concerned about compatibility with the servers in their environment that run Windows.

Which HPE StoreEasy feature addresses the customer's concerns?

A. RESTful API support across a variety of platforms

B. symmetric processor architecture for uniformity in transaction processing

C. use of virtualization technologies to overcome application compatibility issues

D. multi-protocol access to the same file share over SMB and NFS protocols

You are designing a solution to run a Citrix XenDesktop workload. Which HPE planning and designing resource contains a detailed example of this type of solution, including a list of all the hardware and software components?

A. Sales Builder for Windows

B. Product Bulletin

C. Smart Selling Tool

D. Reference Architecture