A network administrator connects several newAruba Instant APs (at factory defaults) to a switch. After
waiting several minutes for the cluster to form, the administrator is ready to provision the cluster. The
VLAN on the ports connected to the APs has no DHCP services.
How can the administrator contact the Instant UI and provision the APs with static IP addresses?
A. Connect to the Instant SSID and open a Web browser.
B. Access the default IP address, 192.168.1.1, from a device connected in the AP VLAN .
C. Access the cluster using Aruba Activate.
D. Access https://vc.arubanetworks.com from a device connected in the AP VLAN.
A network administrator needs to reach an ArubaOS switch CU at a management IP address The
administrator also needs to ensure that the switch entirely rejects Telnet and SSH connections from users
in data VLANs.
How can the administrator meet these goals?
A. Configure the management IP address on the default VLAN and set a manager password.
B. Configure the management IP address on a VTY interface and bind an ACL to this interface.
C. Configure the management IP address on any VLAN except the default VLAN. Set a manager and operator password .
D. Configure the management IP address on the OOBM port and configure the switch to listen for Telnet and SSH only on this port.
Refer to the exhibit.
The exhibit shows the physical connection between two Aruba 5400R switches and a server The network administrator is concerned about redundancy and wants to implement a solution like that shown on the right side of the exhibit. The administrator plans to use an LACP link aggregation with both links active. What must the administrator do first?
A. Configure an LACP link aggregation between the switches.
B. Enable dynamic link aggregation globally on the switches.
C. Combine the switches into a Virtual Switching Framework (VSF) fabric.
D. Configure the same operational key on both the switches.
A network administrator wants to form a cluster with several Aruba Instant APs (|APs). What must the administrator verify?
A. that all APs are pre-configured with WLANs with the same SSID
B. that all APs are operating on the same radio channel
C. that all APs are the same model
D. that all APs are connected in the same subnet
A network administrator needs to configure Virtual Switching Framework (VSF) for the first time on an ArubaOS switch The administrator enters this command: Switch-1(config)# vsf member 1 link 1 a23, a24
The administrator then wants to provision member 2 settings. What must the administrator do before provisioning these settings?
A. Configure SNMP settings that match settings configured on member 2.
B. Enable VSF on the switch and reboot.
C. Join member 2 to the VSF fabric.
D. Specify the model type for member I.
Refer to the exhibits.
A broadcast packet arrives tagged for VLAN 2 on the lVIember 2 link of Trk2. What does lVIember 2 do'?
A. It forwards the packet over the VSF link to Nlember 1. and then Nlember 1 forwards the packet on its link in Trk1.
B. It uses LACP to communicate with the commander on the VSF link, and then follows the commander directions.
C. It uses a hash to select one ofthe links in Trk1, and then forwards the packet locally or on the VSF link, based on the decision.
D. It forwards the packet on its local link in Trk1.
Network administrators manage ArubaOS switches through the CU. What is one prerequisite to enable transfers of completely encrypted config files?
A. Enable the include-credentials option .
B. Install a CA-signed certificate on the switch.
C. Enable TFTPS.
D. Set up SSH.
An ArubaOS switch has no passwords or user accounts configured on it. A network administrator then enters these commands: Switch(config)# password manager user-name admin1 plaintext mysecret1 Switch(config)# password manager user-name admin2 plaintext mysecret2 Switch(config)# aaa authentication local-user admin3 group Level-15 Password plaintext New password for admin3: hpe Please retype new password for admin3: hpe Which users can access the switch CU and use enable and global configuration commands?
A. Admin1 and admin2
B. admin2 and admin3
C. admin1 and admin3
D. admin1 admin2, and admin3
A company wants to deploy Aruba Instant APs (|APs) at branch offices and have a configuration
automatically deployed to the APs.
How can network administrators achieve this goal?
A. Set up an Aruba Activate account and upload configuration templates and provisioning rules to it.
B. Set up configuration templates on AirWave and Aruba Activate provisioning rules that direct the Aps to AirWave.
C. Configure Aruba CIearPass to discover the APs and push configurations to them.
D. Upload a configuration template on a management station and then connect that station to the Instant SSID.
Network administrators need to access an ArubaOS switch CLI remotely. How can the administrator ensure that all data passed between management stations and the switch is encrypted?
A. Create an SSH key, enable SSH, and disable Telnet.
B. Configure operator and manager passwords for Telnet access.
C. Enable HTTPS access.
D. Create local user accounts and enable command authorization.
