HOTSPOT
A network administrator wants to receive a warning level alarm every time the noise floor rises above -82 dBm on any of the AP radios.
Which alarm definition must the network administrator create to accomplish this?
Hot Area:
A company plans to build a resort that includes a hotel with 1610 rooms, a casino, and a convention center. The company is interested in a mobility solution that provides scalability and a service-based approach, where they can rent the
WLAN infrastructure at the convention center to any customer (tenant) that hosts events at the resort.
The solution should provide:
Seamless roaming when users move from the hotel to the casino or the convention center
Simultaneous propagation of the resort and customer-owned SSIDs at the convention center
Null management access upon resort network infrastructure to the customers (tenants)
Configuration and monitor rights of rented SSIDs to the customers (tenants)
Which deployment meets the requirements?
A. Deploy an MM-MC infrastructure with multizone AP's, with one zone for tenant SSIDs.
B. Deploy IAPs along with AirWave, and deploy role-based management access control.
C. Deploy IAPs with zone based SSIDs and manage them with different central accounts.
D. Deploy an MM-MC infrastructure, and create different hierarchy groups for MCs and APs.
E. Deploy IAPs, and manage them with different central accounts.
Refer to the exhibit.
A network administrator deploys DSCP based prioritization in the entire wired network to improve voice quality for a SIP-based IP telephony system used by the company. However, users report that calls they make from WLAN have poor audio quality, while desktop phones do not experience the same problem. The network administrator makes a test call and looks in the datapath session table.
Based on the output shown in the exhibit, what is one area that the network administrator should focus on?
A. UCC based DSCP correction
B. WMM support on the WLAN
C. Dynamic Multicast Rate Optimization
D. wired network congestion
An organization has several RAPs at different locations that broadcast two SSIDs. The internet-only SSID is in bridge/always mode, and the corporate SSID is in split-tunneling/standard mode. The network administrator deploys 10 more
RAPs in different locations.
Users can successfully connect to the corporate SSID that is propagated by a RAP at a remote location. However, they report that it takes too long to access public internet web sites.
What is one part of the configuration that should be checked by the network administrator to verify this RAP deployment?
A. User roles policies
B. IP pool
C. Operating mode
D. Assigned VLAN
Refer to the exhibit.
A network administrator deploys a Mobility Master (MM) - Mobility Controller (MC) network with Aps in different locations. Users in one of the locations report that the WiFi network works fine for several hours, and then they are suddenly
disconnected. This symptom may happen at any time, up to three times every day, and lasts no more than two minutes.
After some research, the network administrator logs into the MM and reviews the output shown in the exhibit.
Based on this information, what is the most likely reason users get disconnected?
A. Adaptive Radio Management is reacting to RF events.
B. AirMatch is applying a scheduled optimization solution.
C. Users in the 2.4 GHz band are being affected by high interference.
D. AirMatch is reacting to non-scheduled RF events.
Refer to the exhibit.
Based on the output shown in the exhibit, which wireless connection phase has just completed?
A. L3 authentication and encryption
B. MAC Authentication and 4-way handshake
C. 802.11 enhanced open association
D. L2 authentication and encryption
Refer to the exhibit
A network administrator deploys a standalone Mobility Controller (MC) and configures some VAPs within the CAMPUS AP group. The network administrator realizes that none of the VAPs are being broadcasted.
Based on the output shown in the exhibit, what should the network administrator do to solve this problem?
A. Install MC-VA licenses, then install PEF licenses and enabled the PEF feature.
B. Install MC-VA licenses, then reprovision the APs.
C. Install MM licenses, then install PEF licenses and enable the PEF feature.
D. Install MM licenses and install MC-VA licenses, then install RFP licenses.
Refer to the exhibits.
A network administrator has fully deployed a WPA3 based WLAN with 802.1X authentication. Later he defined corp-employee as the default user-role for the 802.1X authentication method in the aaa profile. When testing the setup he realizes the client gets the "guest" role.
What is the reason "corp-employee" user role was not assigned?
A. The administrator forgot to map a dot1x profile to the corp-employee aaa profile.
B. The administrator forgot to enable PEFNG feature set on the Mobility Master.
C. MC 1 has not received the configuration from the mobility master yet.
D. The Mobility Master lacks MM-VA licenses; therefore, it shares partial configuration only.
Refer to the exhibit.
A network administrator has Mobility Master (MM) - Mobility Controller (MC) based network and has fully integrated the MCs with ClearPass for RADIUS-based AAA services. The administrator is testing different ways to run user role derivation.
Based on the show command output, what method has the administrator use for assigning the "corp" role to client with MAC xx:xx:xx:xx:xx:xx?
A. Dynamic Authorization using VSA attributes.
B. Dynamic Authorization using IETF attributes.
C. Server Derivation Rules using IETF attributes.
D. User Derivation Rules using the client's MAC.
Refer to the exhibits.
A network administrator deploys User Based Tunneling (UBT) in a corporate network to unify the security policies enforcement. When users authenticate with 802.1X, ClearPass shows Accept results, and sends the Aruba-User-Role attribute as expected. However, the AOS-CX based switch does not seem to build the tunnel to the Mobility Controller (MC) for this user.
Why does the switch fail to run UBT for the user?
A. The switch has not fully associated to the MC.
B. ClearPass is sending the wrong Vendor ID.
C. The switch is not configured with the gateway-role.
D. ClearPass is sending the wrong VSA type.
E. The switch is not configured with the port-access role.
