Click the Exhibit button. Your router is configured to peer with your ISP's router using BGP. You can only control your BGP configuration. Which address families are negotiated between the two BGP peers shown in the exhibit?
A. inet-vpn-unicast
B. inet-unicast inet-vpn-unicast 12vpn
C. inet-unicast inet-vpn-unicast 12vpn-signaling
D. inet-unicast
Which three statements are true regarding not-so-stubby areas (NSSAs)? (Choose three.)
A. You cannot configure an area as both an NSSA and a stub area;
B. An NSSA exports an external route to the backbone area as a Type 5 LSA.
C. An NSSA exports an external route as a Type 3 LSA.
D. An NSSA does not require an ABR.
E. An NSSA imports an external route as a Type 7 LSA.
Click the Exhibit button.
The IS-IS adjacency between routers R1 and R2 will not establish. Referring to exhibit, what is the problem?
A. The ISO address is not configured on interface ge-0/0/1.
B. The level is not configured under protocols isis.
C. The IP address is not configured on interface lo0.
D. The link MTU is too small on interface ge-0/0/1.
Which two OSPF LSA types will you see in a stub area? (Choose two.)
A. network (Type 2)
B. summary (Type 3)
C. ASBR summary (Type 4)
D. external (Type 5)
Click to the exhibit button. Referring to the exhibit, which configuration change is needed for an IS-IS Level 1 adjacency between R1 and R2?
A. Configure the Io0 family ISO address 49.0002.0010.0042.0002.00 on R1.
B. Disable Level 2 on R2'sge-0/0/1 interface.
C. Configure the Io0 family ISO address 49.0002.0010.0042.0002.00 on R2.
D. Enable Level 2 on R1's ge-0/0/1 interface.
Click the Exhibit button.
You have an existing Virtual Chassis consisting of five member devices. Member 3 fails and must be replaced. You remove the EX Series switch with a Member ID and install a replacement switch in its place using identical cabling as shown in the exhibit. The replacement's member ID is 6, so the configuration for member ID 3 is not applied to it. Referring to the exhibit, what should have been done before installing the replacement switch?
A. Reactivate the Virtual Chassis.
B. Recycle the member ID of the switch being replaced.
C. Renumber the member IDs.
D. Clear the Virtual Chassis protocol.
Switch-1 in the exhibit receives a packet from User A with a destination MAC address of
00:26:88:02:74:47.
Which statement is correct in this scenario?
A.
Switch-1 floods the packet out ge-0/0/6, ge-0/0/7, ge-0/0/8, and ge-0/0/9.
B.
Switch-1 floods the packet out ge-0/0/7 and ge-0/0/8.
C.
Switch-1 floods the packet out ge-0/0/7, ge-0/0/8, and ge-0/0/9.
D.
Switch-1 sends the packet out ge-0/0/7 only.
Click the Exhibit button. Referring to the exhibit, which type of route is displayed?
A. static
B. generate
C. aggregate
D. martian
Click the Exhibit button. Based on the trace options output shown in the exhibit, what is the problem with the adjacency?
A. connectivity
B. authentication mismatch
C. area mismatch
D. MTU mismatch
Click the Exhibit button. Referring to the exhibit, which policy will export routes to IBGP peers?
A. static-4
B. static-1
C. static-3
D. static-2
