Your customer has a new FAS2650 HA cluster with ONTAP 9.5 installed. The cluster is connected to two CN1610 switches.
Which two statements describe this installation? (Choose two.)
A. This is a multiple-node installation.
B. This is a single-node installation.
C. The cluster interconnect is in a switched configuration.
D. The cluster interconnect is in a switchless configuration.
A customer ordered two new DS224C shelves. The customer wants you to add these shelves to an existing stack which consists of two DS2246 shelves.
Which statement is true in this scenario?
A. You need to order additional cables to expand the existing stack.
B. Mixing DS224C and DS2246 shelves in the same node are not supported.
C. You cannot mix DS224C and DS2246 shelves in the same stack.
D. DS224C shelves are supports with only new HBAs.
You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.
Which two actions should you perform before you turn over the cluster for production? (Choose two.)
A. Remove cables connected to the controller until you find the one responsible for the controller issue.
B. Review AutoSupport messages which could explain the controller state.
C. Execute Config Advisor again to check for new errors.
D. Let the customer know the cluster is operating normally while the amber LED is on.
You install a new 2-node FAS8200 switchless cluster. You want to reach all necessary management LIFs and SPs for this cluster.
How many management IP addresses do you need in this scenario?
A. 1
B. 2
C. 5
D. 4
You install a new FAS26xx HA system with ONTAP 9.5 at a customer's site. After cabling the SAS cables, the customer wants to cable Alternate Control Path (ACP). But the FAS26xx has no physical port for ACP.
Which statement is correct in this scenario?
A. Within a FAS HA system, the ACP function is established over the cluster interconnect
B. To reach the ACP function, you should put the ACP cable into one of the onboard Ethernet pons.
C. The ACP function is established over the customer network.
D. Beginning with ONTAP 9 software. ACP cabling for disk shelves is no longer required.
Referring to the exhibit(Missing the exhibit), which statement describes the duster network used by the cluster interconnect ports?
A. The network that allows all nodes in the cluster to have direct access to every other node's disk shelves.
B. The network used to allow all nodes to communicate with the users for data access.
C. The network used to allow all nodes to communicate with the customer (or management access.
D. The network used to allow all nodes to communicate for internal (private) data access.
Which statement regarding Epsilon is true?
A. Epsilon is reassigned automatically to the HA partner in case the current owner of the epsilon suddenly reboots.
B. The node holding the epsilon has extra fractional vote weight.
C. Whenever a new node is added, the epsilon is automatically reassigned to this node.
D. The epsilon acts as a tiebreaker in a 2-node cluster.
You want to grow your current ONTAP cluster. You have a Cisco Nexus 5596UP that is currently using all of its on-board ports.
Which statement is correct in this situation?
A. Contact NetApp Support to order new switches.
B. Add expansion modules to the Cisco switches.
C. Pull the redundant cables from each node to obtain more free ports on the switch.
D. Add new SFP modules to the empty on board ports on the Cisco switches.
You have a 6-node ONTAP 9.1 cluster with two FAS6290 nodes and four FAS8080 EX nodes using a SAN protocol.
In this scenario, how many FAS9000 HA pairs would be joined to this cluster?
A. 3
B. 2
C. 9
D. 6
You have just added a new DS4246 shelf with 24 x 10 TB SATA HDDs to a single FAS2650 node as the
first SATA shelf. You must keep two SATA spare disks on the shelf.
What is the maximum number of SATA data disks available in this scenario?
A. 19
B. 16
C. 22
D. 20
