On a FAS8040, which port is used for FCoE connections?
A. e0M
B. e0P
C. 0a
D. e0h
Click the Exhibit button.
Referring to the diagram shown in the exhibit, what will happen if PDU-B fails?
Exhibit:
A. Both Node A and Node B will remain online and all disk shelves will remain online.
B. Both Node A and Node B will remain online, but all disk shelves will immediately lose power and become inaccessible.
C. Both Node A and Node B will immediately lose power and become inaccessible.
D. Node A will immediately lose power and become inaccessible. Node B will remain online.
You have a 4-node FAS8040 cluster licensed for FCP and iSCSI. Each node has both FC and iSCSI LIFs. One of your Windows 2012 Servers has a single 8Gb FC port and a single 10 Gb Ethernet port with switched connectivity to the FC and Ethernet ports on the cluster. You need to use both ports on the host for multipath access to a LUN on the NetApp cluster.
What will accomplish this task?
A. NetApp Data ONTAP DSM for Windows MPIO
B. FCoE HBA
C. iSCSI HBA
D. native Windows MPIO
When designing a new SAN solution, which three components should be verified with the IMT? (Choose three.)
A. the connection protocol
B. the patch panel make and model
C. host OS type and version
D. the type of Ethernet switch
E. the clustered Data ONTAP version
A company has 50 ESXi hosts connected using FC to a single target port on a NetApp cluster. Ten hosts are configured with an HBA queue depth on 128. Forty hosts are configured with a HBA queue depth of
32. They are experiencing performance problems with their FC LUNs. Which two actions will resolve the problem? (Choose two.)
A. Use VSC to set recommended values for the hosts.
B. Reduce the HBA queue depth on the on the applicable HBAs.
C. Add additional target ports to allow for greater initiator distribution.
D. Increase the total queue depth on the NetApp cluster.
Which two flags would you use to enable NetApp thin provisioning on a LUN? (Choose two.)
A. -space-reserve enabled -space-allocation enabled
B. -space-reserve enabled -space-allocation enabled
C. -space-reserve disabled -space-allocation disabled
D. -space-reserve disabled -space-allocation enabled
A customer has a host experiencing performance problems with its FC LUNs. The customer has examined the nodes hosting the LUNs, and both the disk and CPU performance are below 50% utilization. The
customer examined the switch ports connected to the storage array, and they are also below 50% utilization.
Which three should the customer verify? (Choose three.)
A. that the HBA queue depth is set properly
B. that the host HBA has the correct port settings
C. that the host Ethernet interfaces are using jumbo frames
D. that the host is running SnapDrive
E. that the FC switch ports connected to the host have not exceeded the maximum capacity
Exhibit
You currently have the following configuration on your cluster:
cl01::>igroup show -instance Vserver Name: svm1 Igroup Name: ig2 Protocol: mixed OS Type: linux Portset Binding Igroup: -Igroup UUID: 3fb136c7-cfd6-11df-a9ab-123478563412
Initiators:
What must you do to limit the LIFs that are used by an initiator to access a LUN?
A. Create a portset.
B. Create an additional igroup.
C. Change the protocol to iSCSI.
D. Change the OS type to windows_gpt.
Exhibit
cl01::>lun resize -vserver svm1 -volume db1_vol -lun db1 -size 4096g Error: command failed: New size exceeds this LUN's initial geometry cl01::>
What is the reason for the error shown in the exhibit?
A. The LUN is thin provisioned, but the parent volume is thick provisioned and cannot satisfy the request.
B. The aggregate over commitment threshold has been exceeded.
C. The parent volume that contains the LUN is out of space.
D. The LUN cannot be grown past its maximum resize size.
Which protocol allows to access a controller's CLI interface?
A. SSH
B. NTP
C. TFTP
D. IMAP
